🐵 Honda Xr 125 Fork Oil Capacity

The beauty of the conventional forks is that you can add oil with the forks still on the bike. So if you measure 130 from the top and the bike bottoms too harshly, undo one cap at a time and let the weight of the bike push the assemly up a bit. Get a Baby Tylenol syringe and add five mm at a time until the bottoming reistance feels good. Use The Seal Driver. With the oil seal on get out your seal driver and rubber mallet. Placing the driver on the edge of the seal, take the mallet and strike the seal driver to force the seal down. It will take a reasonable amount of force from the mallet but start softly and build up. Hey I’ve done a tone of testing on forks with the bbr springs and rods I recommend 30wt oil and 130 from the top with the fork completely compressed and the spring out then also don’t put the preload spacer back in. With the spacer in it makes it feel kinda pogo when you hit bigger jumps hope this helps! This is an older thread, you may not Posted July 21, 2009. according to my manual '86-'89 forks should be 535cc. nick. My manual says the same. You can use more or less oil to provide more or less damping. Maximum oil level, measured from the top of the tube with the springs out and fork collapsed, is 125mm (more damping) Minumum level is 165mm (less damping). Oil capacity: 250R 86-89 18.1 oz. 90-95 16.6oz. 96 on 16.13 oz or 477cc. 400R 19 oz. 1996 Honda XR250R: Standard Maintenance Interval: 1,609.34km (1,000mi) Break-in Interval: 321.87km (200mi) Engine Oil Change Interval: 1,609.34km (1,000mi) Initial Valve Check: 321.87km (200mi) Periodic Valve Check: 1,609.34km (1,000mi) Engine Oil Capacity With Filter Change: 1.4L (0.37gal.) More on Engine Oil: Pro Honda Gn4 HP4 4-stroke 2008 Honda XR 125 L fork oil capacity. 2008 Honda XR 125 L; Open Questions: 0 answers. 2004 Honda XR 125 L how to disassemble the front forks. Read full answer. This is my first time doing fork oil and bike is 1987 Honda XL250R, has forks similar to XR200 and XR250 with the air fill on fork cap. As per my waste of money Clymer manual states, all I need to do is drain the forks by removing the drain plug at bottom, unscrew the top fork cap, remove spring, push down and fill with 293cc of oil until it Posted March 29, 2013. So pull the forks and change the oil. Easy enough! Pull the front wheel and brake calipra off. Then loosen the top triple tree and leave the bottom one tight. Then loosen (JUST LOOSEN) the top fork tube caps. Now loosen the bottom triple tree clamp and remove the tubes. Unscrew the fork cap. However, use what makes you feel warm and fuzzy inside!!! My specs came directly from Honda 's OEM service manual, 1985, page 11-14 11-15. Not sure why the other chap's specs are different. Not when you consider the variation in viscosity among the different brands. Maxima 10wt fork oil has a viscosity of 32 cSt @ 40C. Racer. Posted July 30, 2008. The XR75 requires 3.6~3.7oz. of Dexron auto trany fluid or Honda fork oil in each fork leg. Honda XR125 L Specs. The Honda XR125 L model is a Enduro / offroad bike manufactured by Honda . In this version sold from year 2014 , the dry weight is 129.0 kg (284.4 pounds) and it is equipped with a Single cylinder, four-stroke motor. The engine produces a maximum peak output power of and a maximum torque of . q4OAF.

honda xr 125 fork oil capacity